Jump to content


2

It is possible to have gigabit interfaces instead of eth in ASAv and IOL?


4 replies to this topic

#1 522690

522690

    Advanced Member

  • Members
  • PipPipPip
  • 112 posts
  • 72 thanks

Posted 08 February 2019 - 03:26 AM

Hello, all!
It is possible to have gigabit interfaces instead of eth in ASAv and IOL?
I mean interface names in conf t - interface gig 1/0 instead of eth 0.

Thanks!

#2 MrR0b0t

MrR0b0t

    Cisco Technologies Expert.

  • Technical Expert
  • PipPipPip
  • 130 posts
  • 8945 thanks

Posted 08 February 2019 - 06:28 AM

ASSv already has gig interfaces but not IOL
"Do not mistake my Generosity for generosity."
______________________________________________________

-> Do not post useless "thank you" post.
-> Please use the "Thanks" button as shown in the  announcements
-> Help us keep this forum clean by reporting spam / scam / non IT related posts.
-> Please use report button to report posts / users.

#3 522690

522690

    Advanced Member

  • Members
  • PipPipPip
  • 112 posts
  • 72 thanks

Posted 08 February 2019 - 07:28 AM

View PostMrR0b0t, on 08 February 2019 - 06:28 AM, said:

ASSv already has gig interfaces but not IOL

Well, not in my case. I am using this version of ASAv:
ASA1# show version

Cisco Adaptive Security Appliance Software Version 9.1(5)16

And there are only eth interfaces:

ASA1# sh int ip br
Interface   IP-Address   OK? Method Status Protocol
Ethernet0   20.1.1.1 YES manual up up  
Ethernet1   10.1.11.1    YES manual up up  
Ethernet2   10.10.11.1   YES unset  up up  
Ethernet3   unassigned   YES unset  administratively down up  
Ethernet4   unassigned   YES unset  administratively down up  
Ethernet5   unassigned   YES unset  administratively down up  
Ethernet6   unassigned   YES unset  administratively down up  
Ethernet7   unassigned   YES unset  administratively down up

Probably, changing of ASA template could cause it?
https://certcollection.org/forum/topic/321827-cisco-asa-915-clustering-and-security-contexts-enabled/page__st__28#entry1238049

Edited by 522690, 08 February 2019 - 07:34 AM.


#4 MrR0b0t

MrR0b0t

    Cisco Technologies Expert.

  • Technical Expert
  • PipPipPip
  • 130 posts
  • 8945 thanks

Posted 08 February 2019 - 07:52 AM

View Post522690, on 08 February 2019 - 07:28 AM, said:

Well, not in my case. I am using this version of ASAv:
ASA1# show version

Cisco Adaptive Security Appliance Software Version 9.1(5)16

And there are only eth interfaces:

ASA1# sh int ip br
Interface   IP-Address   OK? Method Status Protocol
Ethernet0   20.1.1.1 YES manual up up  
Ethernet1   10.1.11.1    YES manual up up  

Because that is not ASAv!! its ASA 9.1.5 and a hacked HW image. IIRC, this is pulled from a 5520 ASA appliance so its HW appliance code which at that time had only ethernet interfaces.
"Do not mistake my Generosity for generosity."
______________________________________________________

-> Do not post useless "thank you" post.
-> Please use the "Thanks" button as shown in the  announcements
-> Help us keep this forum clean by reporting spam / scam / non IT related posts.
-> Please use report button to report posts / users.

#5 522690

522690

    Advanced Member

  • Members
  • PipPipPip
  • 112 posts
  • 72 thanks

Posted 08 February 2019 - 08:14 AM

View PostMrR0b0t, on 08 February 2019 - 07:52 AM, said:

Because that is not ASAv!! its ASA 9.1.5 and a hacked HW image. IIRC, this is pulled from a 5520 ASA appliance so its HW appliance code which at that time had only ethernet interfaces.
Oh, then  sorry for silly question. I will find ASAv image and check interfaces  there.

Thanks!




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

Organization

Community

Downloads

Test Providers

Site Info


Go to top